Skip to main content

LM2902 Low Power Quad Operational Amplifiers

The LM2902 Op-Amp is a low-cost, high-Performance Quadruple Operational Amplifier, i.e. it consists of four independent high-gain frequency-compensated operational amplifiers that are designed specifically to operate from a single supply or split supply over a wide range of voltages.

 

LM2902 Op-Amp Pinout Configuration

Pin Number

Pin Name

Description

1

OUTPUT 1

Output of Op-Amp 1

2

INPUT 1-

Inverting Input of Op-Amp 1

3

INPUT 1+

Non Inverting Input of Op-Amp 1

4

V+

Supply Voltage

5

INPUT 2

Non Inverting Input of Op-Amp 2

6

INPUT 2-

Inverting Input of Op-Amp 2

7

OUTPUT 2

Output of Op-Amp 2

8

OUTPUT 3

Output of Op-Amp 3

9

INPUT 3-

Inverting Input of Op-Amp 3

10

INPUT 3+

Non Inverting Input of Op-Amp 3

11

GND

Ground or Negative(Dual Polarity Supply)

12

INPUT 4+

Non Inverting Input of Op-Amp 4

13

INPUT 4-

Inverting Input of Op-Amp 4

14

OUTPUT 4

Output of Op-Amp 4

 

Features & Specifications 

  • Wide Supply Voltage Range 3V to 32V
  • Internally Frequency Compensated for Unity Gain
  • Large DC Voltage Gain 100 dB
  • Dual Polarity Supply ±1.5 V to ±16 V
  • Low Supply-Current Drain Independent of Supply Voltage: 0.8 mA Typical
  • Common-Mode Input Voltage
  • Input Offset Voltage: 2 mV Typical
  • Input Offset Current: 5 nA Typical
  • Input Bias Current: 45 nA Typical
  • Open-Loop Differential Voltage Amplification 100 V/mV Typical
  • Internal Frequency Compensation
  • 2-kV ESD Protection
  • Unity-gain Bandwidth 1 MHZ

 

Note: Complete technical details can be found in the LM2902 datasheet given at the end of this page.

 

LM2902 Equivalent Op-Amps

LM324, LM335, LM358, LM393

 

Where to use LM2902 Op-Amp

The LM2902 is a Quad Package Operational Amplifier, meaning it has four Op-Amps inside it and each Op-Amp can be used independently.

LM2902 Pin Diagram

The LM2902 series consists of four independent, high-gain, internally frequency compensated operational amplifiers designed to operate from a single power supply over a wide range of voltages. Operation from split-power supplies is also possible and the low-power supply current drain is independent of the magnitude of the power supply voltage.

Application areas include transducer amplifiers, DC gain blocks and all the conventional op amp circuits which now can be more easily implemented in single power supply systems. For example, the LM2902 series can directly operate off of the standard 5-V power supply voltage which is used in digital systems and easily provides the required interface electronics without requiring the additional ±15 V power supplies.

 

How to use LM2902 Op-Amp

We can use this IC for audio pre-amplification, basic comparator, adder, and subtractor devices.

LM2902 Simulation Circuit

In the above circuit, the LM2902 Op-amp is configured as a non-inverting configuration. The gain of the op-amp is set to 10. For that, we have used a 1K resistor and a 9.1K resistor, as you can see for the simulation, we have used a variable potentiometer. By varying the potentiometer, we can vary the input voltage and the output voltage will also vary, to power the op-amp, we have used +12V and -12V supply, as the gain of the op-amp is 10, so if we provide 1V at the input, we will get 10V at the output, the simulated circuit shows exactly that.
 

Applications 

  • Blu-ray Players and Home Theatres
  • Chemical and Gas Sensors
  • DVD Recorders and Players
  • Digital Multimeter: Bench a. Systems
  • Digital Multimeter: Handhelds
  • Transducer Amplifiers
  • DC Gain Blocks
  • Conventional Op Amp Circuits

 

2D Model and Dimensions

If you are designing a PCB or Perf board with this component, then the following picture from the LM2902 Datasheet will be useful to know its package type and dimensions.

LM2902 Dimensions 

Component Datasheet

Related Post



Join 20K+subscribers

We will never spam you.

* indicates required

Be a part of our ever growing community.